Model 310H 800 V Electric Pulse Module
800 V Electrical Pulse Module
The Model 310H is a 800V electrical plug in for the BNC Model 6040 Electro/Optic Pulse Generator Mainframe
OVERVIEW
FAST 800 V PULSES INTO 50 Ω LOAD
Model 310H adapts the Mainframe 6040 to amplitude requirements of up to 800V for 50 Ω loads. The operating capabilities of the 6040/310H provide outputs in the form of 1 ns resolution digital delays and gates and PRFs from .01 Hz to 100 kHz (or one-shots), in both single and double pulse formats. Leading edge transitions are 10 ns or less and trailing edges as low as 10 ns. Polarity is switch selectable and pulse width can range from a minimum of 25 ns up to 20 us.
The 6040/310H combination retains the high timing accuracy, low jitter, nanosecond resolution, memory storage, and programmability available with other installed 6040 modules. Also, the 310H self-protects against damage from operation at excessive duty factors or into a short circuit, with a light signaling overload conditions. Refer to the eight-page Model 6040 product bulletin or at this site for additional detailed information on equipment operation, a timing diagram, and applications.
FEATURES
Trigger Internal 0.01 Hz to 40 KHz; external 0 to 40 KHz
Pulse Width 20 ns to 640 s
Delay 0 ns to 640 s (plus fixed delay)
APPLICATIONS
Photo Multiplier
Photo Detector
Fiber Optics Testing
SPECIFICATIONS
PULSE OUT
Amplitude
100 V to 800 V into 50 ohms. Fixed 0 V baseline. Polarity internally switch selectable.
Resolution
5 V (to max. amplitude).
Linearity
+/- 1%.
Transition Times (10% to 90%)
Leading edge: < 10 ns. Trailing edge: between 200 V and 750 V, 10 ns. Other amplitudes, 15 ns max.
Max. Power
16.2 W average, 16.2 kW peak (at 800 V).
Max. Current
18 A peak.
Droop
1%/~s max.
Aberrations
+/- 10% of amplitude.
Connector
Type N.
TIMING
Trigger
Internal 0.01 Hz to 40 kHz at 800 V. to 50 kHz at 800 V, to 100 kHz at 600V or less; external 0 Hz to same maximums as above.
Pulse Width
25 ns to 20 uS (see Droop). Calibrated at 500 V; at other amplitudes true witdhs vary slightly in fixed value up to 10 ns max.
Duty Factor
0.1% max. at 800 V. Duty factors increase up to 9% at 100 V.
Delay
0 ns to 640 s (plus fixed delay).
Minimum Interpulse Separation
500 ns (trailing to leading edges).
Module Delay
30 ns typical (fixed) mainframe's Pulse Out to module's Pulse Out. Jitter 50 ps rms.
ACCESSORIES
Coaxial 50-Ohm Load ResistorPart Number 6860
Rated for 100 W continuous and 20 kW peak (800 V <20 us pulses). For terminating the 310H into high impedance loads or substitute for inadequate average or peak power-dissipating 50 ohm terminations. 7"L x 2 3/4" Sq (178 x 70 mm).
COMMON MODULE SPECIFICATIONS
Store
ROM determines the instrument's allowable operating conditions and units of display applicable for the installed module.
A nonvolatile memory (RAM) in each module stores up to ten complete settings of operating conditions (trigger level, slope, etc.) and output pulse parameters.Recall
The RAM-stored settings can be manually or bus transferred to the mainframe to produce the pre determined outputs.
Weight
2 Ibs net (0.9 kg); 5 Ibs shipping (2.3 kg).
Ambient
Same as Model 6040 mainframe.
描述 [描述] 型号310H是用于BNC型号6040电光脉冲发生器主机的800V电源插头