High Energy kHz Pulsedu Cavity Dumped DPSS Nd:YAG Lasers
kHz pulsed cavity dumped DPSS Nd:YAG lasers
Up to 10 mJ at 1064 nm
Up to 1 kHz repetition rate
Close to TEM00 beam profile
FEATURES 10 mJ at 1064 nm
1 kHz pulse repetition rate
All-solid-state design
Internal/external triggering
Short warm-up time
Built-in water-to-air chiller (external water service is not required)
Optional temperature stabilized second, third and fourth harmonic generators
PC control via USB (RS232 is optional) with supplied LabVIEW™ drivers
Remote control via keypad
APPLICATIONS
OPO pumping
Laser spectroscopy
Material ablation
Micromachining
Remote sensing
Description
NL210 series diode pumped Q-switched lasers produce up to 10 mJ at 1000 Hz pulse repetition rate. The laser is designed to produce high intensity, high brightness pulses and is targeted for applications like OPO pumping, nonlinear spectroscopy, material ablation, micromachining, and other tasks.
Employing electro-optical type of the cavity dumping, the master oscillator can produce pulses with a short pulse duration of 3 – 4 ns, the uniform beam profile and low divergence. The M² factor of the beam is typically between 3 – 4. Laser cooling uses a closed loop chiller, thus eliminating the need for external cooling water, and reducing running costs.
Angle-tuned LBO and/or BBO crystals mounted in temperature stabilized heaters are used for optional second, third or fourth harmonic generation. The harmonic separation system is designed to ensure a high spectral purity of radiation directed to separate output ports.
For customer convenience the laser can be controlled from a remote control pad or USB interface. The remote pad allows easy control of all parameters and features a backlit display that is easy to read even wearing laser safety eyewear. Alternatively, the laser can be controlled from a personal computer with supplied software for a Windows™ operating system. LabVIEW™ drivers are supplied as well.
Specifications
Model NL210 MAIN SPECIFICATIONS 1)
Pulse energy:
at 1064 nm
10 mJ
at 532 nm 2)
5 mJ
at 355 nm 3)
3 mJ
at 266 nm 4)
1 mJ
Pulse to pulse energy stability, 5)
at 1064 nm
< 1.0 % rms
at 532 nm 2)
< 2.0 % rms
at 355 nm 3)
< 2.5 % rms
at 266 nm 4)
< 4.0 % rms
Pulse duration 6)
3 – 4 ns
Pulse repetition rate
1000 Hz
Beam profile
multimode
Elipticity
0.9 – 1.1 at 1064 nm
M2
< 4
Beam divergence 7)
< 2 mrad
Beam pointing stability, StDev
< 50 µrad
Polarization
linear, > 95 %
Typical beam diameter 8)
2 mm
Pulse jitter wrt to SYNC OUT, StDev 9)
< 0.5 ns
Pulse jitter wrt to ext. trigger, StDev 10)
< 0.5 ns
PHYSICAL CHARACTERISTICS
Laser head (W × L × H)
456 × 1031 × 260 mm
Power supply unit (W × L × H)
520 × 400 × 290 mm
Umbilical length
3 m
OPERATING REQUIREMENTS
Cooling 11)
Built-in chiller
Ambient temperature
18 – 27 °C
Relative humidity
20 – 80 % (non-condensing)
Power requirements
100 – 240 V AC, single phase, 50/60 Hz
Power consumption
< 1 kVA
1)Due to continuous improvement, all specifications are subject to change without notice. Parameters marked typical are not specifications. They are indications of typical performance and will vary with each unit we manufacture. Unless stated otherwise, all specifications are measured at 1064 nm and for basic system without options.
2)For NL210-SH option. Outputs are not simultaneous. The laser performance is specified for SH wavelength; specifications for other wavelengths may differ from that indicated above.
3)For NL210-SH/TH option. Outputs are not simultaneous. The laser performance is specified for TH wavelength; specifications for other wavelengths may differ from that indicated above.
4)For NL210-SH/FH option. Outputs are not simultaneous. The laser performance is specified for FH wavelength; specifications for other wavelengths may differ from that indicated above.
5)Averaged from pulses, emitted during 30 sec time interval.
6)FWHM.
7)Full angle measured at the 1/e² point at 1064 nm.
8)Beam diameter is measured at 1064 nm at the 1/e² point.
9)Optical pulse jitter with respect to SYNC OUT in internal triggering mode.
10)Optical pulse jitter with respect to QSW IN in external triggering mode.
11)Air cooled
Note: Laser must be connected to the mains electricity all the time. If there will be no mains electricity for longer that 1 hour then laser (system) needs warm up for a few hours before switching on.
Performance & Drawings
Ordering Information
商品属性 [波长] 1064nm/532nm/355nm/266nm [脉宽] 3 – 4 ns [重复频率] 1000Hz [单脉冲能量] 10mJ/5mJ/3mJ/1mJ