1030 NM LASER (DPSS; SMA PORT)
描述
1030 nm laser with SMA output is a very compact high performance laser source for multimode fiber installations. Fiber could be supplied optionally.
产品规格
Parameter
Minimum Value
Typical Value
Maximum Value
Central Wavelength, nm
1028
1030
1032
Longitudinal modes
-
multimode
-
Spectral line width FWHM, nm
-
0.7
1
Output power, mW
-
400 1
-
Fiber coupling efficiency, %
50
70 2
80
Fiber core diameter, ÎĽm
50
105
200
Power stability, % (RMS, 8 hrs)
-
1 3
2
Power stability, % (peak-to-peak, 8 hrs)
-
2 4
3
Noise, % (RMS, 20 Hz to 20 MHz)
-
3 5
30
Transversal modes
-
multiple
-
Control interface type
-
UART/USB
-
Operation mode
-
APC (CW)
-
Modulation bandwidth, MHz
-
N/A 6
-
Input voltage, VDC
4.8
5
5.3
External power supply requirement
-
+5 V DC, 5 A
-
Dimensions, mm
-
50 x 30 x 18 7
-
Heat-sinking requirement, °C/W
-
0.5
-
Optimum heatsink temperature, °C
15
20
30
Warm up time, mins (cold start)
0.2
1
2
Temperature stabilization
-
Yes
-
Overheat protection
-
Yes
-
Storage temperature, °C (non-condensing)
-10
-
50
Net weight, kg
0.1
0.12
0.14
Max. power consumption, W
5
10
20
Warranty, months (op. hrs)
-
14 (10000) 8
-
RoHS
-
Yes
-
CE compliance
-
- General Product Safety Directive (GPSD) 2001/95/EC
- (EMC) Directive 2004/108/EC-
Laser Safety Class
-
3B
-
OEM lasers are not compliant with
-
IEC60825-1:2014 (compliant using additional accessories)
-
1 The optical power can be tuned from virtually 0% to 100%. However, other specifications, such as central wavelength, power stability, noise, polarization ratio, beam shape, quality and circularity are not guaranteed at power levels other than factory preset power. Significantly worse power stability is to be expected at very low power levels, e.g. <3% from specified nominal power.
2 Output power is heavily dependent on fiber insertion repeatability.
3 The long term power test is carried out at constant laser body temperature (+/-0.1 °C) using an optical power meter with an input bandwidth of 10 Hz. The actual measurement rate has a period of about 20 seconds to 1 minute.
4 The long term power test is carried out at constant laser body temperature (+/-0.1 °C) using an optical power meter with an input bandwidth of 10 Hz. The actual measurement rate has a period of about 20 seconds to 1 minute.
5 Noise level is measured with a fast photodiode connected to an oscilloscope. The overall system bandwidth is from 2 kHz to 20 MHz.
6 Modulation of DPSS lasers is limited to a few kHz by physics. Therefore we recommend to modulate the laser by sending commands through UART interface. The TTL pin of DPSS lasers is configured to provide PWM signal for control of fan speed instead of modulation.
7 Excluding control interface pins and an output window/fiber assembly.
8 Whichever occurs first. The laser has an integrated operational hours counter.
Note: Product specifications are subject to change without prior notice to improve reliability, function or design or otherwise.
Drawing
商品属性 [波长] 1030nm [功率] 400mW [输出类型] DPSS; SMA PORT