DIODE PUMPED SUB-NANOSECOND PASSIVELY Q-SWITCHED LASER
MPL1310 series DPSS passively Q-switched sub-nanosecond lasers deliver > 3 MW high peak powers at 100 Hz repetition rate. Short laser cavity is fixed on thermo-stabilized and controlled baseplate which gives extremely stable output parameters. Small footprint is welcome point for integration into OEM lasers. Sub-nanosecond pulse duration of < 350 ps, high pulse energy more than > 1 mJ, variable repetition rate from 1 Hz to 100 Hz covers many applications like medical, surface disinfection, supercontinuum generation and many others.
Due to short pulse duration and high pulse energy laser delivers high peak power which is > 3 MW. Optional conversion to green (532 nm) and ultraviolet (355 nm, 266 nm) is available.
Features
Applications
More than 1 mJ pulse energy at 1064 nm
Short pulse duration < 350 ps (optional < 250 ps)
Variable up to 100 Hz repetition rate
532 nm, 355 nm, 266 nm harmonics
Average power 100 mW
High peak power > 3 MW
Guaranteed > 3 Gshot lifetime
Other wavelengths (e.g. 1053 nm, 1342 nm, 671 nm, 447 nm, 914 nm) are available
Medical
Surface disinfection
Laser induced breakdown spectroscopy (LIBS)
Time resolved fluorescence measurements
DNA analysis
Remote sensing
Supercontinuum generation
Ignition of gas mixtures
Model
MPL2310
MPL1310
MPL1310-MO
Pulse energy:
at 1064 nm
> 2 mJ
> 1 mJ
> 0.2 mJ
at 532 nm
> 1 mJ
> 0.5 mJ
> 0.1 mJ
at 355 nm
> 0.5 mJ
> 0.25 mJ
> 0.05 mJ
at 266 nm
> 0.25 mJ
> 0.15 mJ
–
Typical pulse duration
< 350 ps 2)
< 350 ps 2)
200 ps 2)
Pulse to pulse energy stability (RMS):
at 1064 nm
< 1 % 3)
at 532 nm
< 2.5 % 3)
at 355 nm
< 3.5 % 3)
at 266 nm
< 5.0 % 3)
Power drift
± 3.0 % 4)
Pulse repetition rate 5)
1 – 100 Hz
Beam profile
Close to Gaussian
Beam divergence 6)
< 5 mrad
Polarization
Linear, horizontal at 1064 nm
Spectral Linewidth
SLM
Beam pointing stability 7)
< 30 µrad
Typical beam diameter 8)
1.5 mm
1 mm
Jitter
~ 2 µs RMS 9)
Dimensions
Laser head (W×L×H)
83 × 157 × 41.5 mm
Controller unit (W×L×H)
75 × 200 × 70 mm (OEM version)
Power adapter (W×L×H)
119 × 179 × 30 mm (OEM version)
Operating requirements
Cooling requirements
Air cooled
Ambient temperature
15 – 30 ºC
Relative humidity (non-condensing)
10 – 80 %
Mains voltage
100-230 VAC, single phase, 50-60 Hz 10)
Power consumption
< 20 W
< 10 W
1. Due to continuous improvements all specifications are subject to change. Unless stated otherwise all specifications are measured at 1064 nm.
2. FWHM level at 1064 nm. Other pulse duration is available by request. Please inquire for detailed specifications.
3. Averaged from 60 seconds time interval.
4. Over 8-hour period after max 5 minutes of warm-up when ambient temperature variation is less than ±2 °C.
5. Factory-set pulse repetition rate is fixed at max repetition rate. Higher repetition rates are available, please inquire for details.
6. Full angle measured at the 1/e2 level.
7. RMS value measured from 1000 shots in 5 series.
8. Beam diameter is measured 20 cm from laser output at the 1/e2 level.
9. In respect to Q-switch triggering rising edge pulse.
10. Laser can be powered from an appropriate 12 VDC power source. Please inquire for more details.
Laser head dimensions:
商品属性 [波长] 1064nm 532 nm 355 266 nm [脉宽] < 350 ps [单脉冲能量] at 1064 nm> 2 mJ, at 532 nm> 1 mJ,at 355 nm> 0.5 mJ, at 266 nm> 0.25 mJ